We have stumbled upon this great article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the net and accepted it made perfect sense to discuss it with you on this site.
Setting up a tub isn't specifically rocket science, but it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately tough project. If the old bathtub is easily available, the job can move quickly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old bathtub and set in the new one. Make sure you have qualified yourself for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you might require a specialist plumber to make tube links.
This short article will help you install a brand-new bath tub in your shower room if you have actually already bought a new bathtub and also don't need to change the setup of your previous water system pipes.
Your tools and also product checklist need to make up the following:
Planning for the Installation
To start with, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to avoid pressure on the tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use all of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The process of removing the existing taps can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have actually been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are helpful in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub till the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression join; then do the very same for the other faucet.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub as well as also examine the overflow outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub needs to wait until the bath tub has actually been used at the very least once as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet adapters. The previous type should be attached to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, creating the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and also fittings. They are marketed in tubes and cartridges, as well as are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to enable the movement experienced when the tub remains in usage. The sealer can crack rather early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive and also cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
We were shown that editorial about How to Install a Bathtub Yourself from a friend on another site. Feel free to set aside a second to distribute this article if you liked it. I take joy in reading our article about How to Install a Bathtub.
Further Details